Att wall phone manual

All rights reserved. Printed in Mexico. Please also read Part 1 —. Important Product Information. Previous Page. Next Page. Use this cord to connect the telephone to a modular jack. Fill in directory card Remove the directory card and write in your own telephone number.

Also write the telephone num- bers or names that you want to store in each memory location. Reverse handset tab To install the telephone on a wall jack, you must reverse a small tab beneath the directory card.

Install telephone base on wall jack Hold the base up next to the wall jack, and plug in the line cord Figure 3. Customer Instruction Booklet. Partner MLS 12D. Partner MLS 18D. Partner MLS 34D. Partner MLS 6. Plant Series. Private Pay Phone. Service And Reference Manual.

Small Business System Speakerphone. Syn SB Synapse SB SynJ SB System Telephone Adapter. Install Manual. Touch-a-Matic S Series. Trimline Trimline Single Line Business Telephone.

Trimline TR Bundles Single handset 4 handsets 7 handsets 2 handsets 5 handsets 8 handsets 3 handsets 6 handsets. Manuals and Videos Please enter your model number in the box below to find the manual and quick start guide. Model number: Turn over the base of your phone to locate the model number as illustrated in the image below.

All rights reserved. Error message. Press to switch to tone dialing temporarily during a call if you have pulse service page When reviewing directory entries, press to move towards the end of the telephone number page When reviewing directory entries, press to move towards the beginning of the telephone number page Press repeatedly to display other dialing options when reviewing a caller ID log entry page Move the top of the display forward or backward to adjust the angle of the screen for maximum visibility.

During message playback or call screening, press to adjust the listening volume pages 40 and Install the telephone base close to a telephone jack and a power outlet not controlled by a wall switch. The telephone base can be placed on a flat surface or vertically mounted on the wall see pages If you subscribe to high-speed Internet service DSL - digital subscriber line through your telephone line, you must install a DSL filter between the telephone line cord and the telephone wall jack see page 4.

Your product may be shipped with a protective sticker covering the telephone base display, remove it before use. For customer service or product information, visit our website at www.

The telephone is ready for tabletop use. If you want to change to wall mounting, see Installation options on page 6 for details. Plug one end of the coiled handset cord into the handset jack on the left side of the telephone base. Route the telephone line cord through the slot. Plug the other end of the telephone line cord into a telephone wall jack or a DSL filter.

Route the power adapter cord through the slot. Adjust the angle of the screen to reach maximum visibility. To obtain a replacement, visit our website at www. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

See Line power mode on page If you want to mount your telephone on a wall, use the provided wall mount bracket to connect with a standard dual-stud telephone wall mounting plate. If you do not have this mounting plate, you can purchase one from many hardware or consumer electronics retailers. Professional assistance may be required to install the mounting plate. To install the telephone base in the wall mount position, make sure you first unplug the power adapter cord and telephone line cord from the telephone base and wall outlets.

Lift the handset and place it aside. Hold down the switch hook on the telephone base, then slide the handset tab upwards to remove it from the slot. Rotate the handset tab degrees. Push the handset tab down into the slot so it locks into position. Align the tabs on the wall mount bracket to the slots at the back of the telephone base. Insert tab A on the top into its corresponding slot and click tabs B into their corresponding slots.

Plug the other end into a telephone wall jack or a DSL filter. Bundle the telephone line cord and secure it with a twist tie. Place the telephone just above the studs on the wall mounting plate. Slide the telephone down until it is held securely on the wall mounting plate. Place the handset on the telephone base. To change the telephone base from the wall mount position to tabletop position, follow the steps below.

Slide the telephone base upwards, then remove the telephone from the wall mounting plate. Unplug the large end of the power adapter from the electrical outlet. Remove the power adapter cord from the slot. Unplug the smaller end from the power jack on the bottom of the telephone base. Unplug the telephone line cord from the wall jack and the telephone base. Untie the bundled telephone line cord. Push the handset tab down into the slot so it clicks into position.

Push the two tabs at the bottom of the wall mount bracket as indicated and remove the wall mount bracket from the telephone.